A hands-on introduction to using chisels, hand planes and saws safely and correctly. Every participant works on timber throughout the session, building confidence through guided practical exercises. No prior experience required, perfect for beginners.

Learning Outcomes

By the end of the workshop, participants should be able to:

Safely set up and secure timber for hand-tool work.
Use common hand saws, chisels and planes with correct technique.
Understand grain direction and how it affects cutting and planing.
Make basic straight cuts, recesses and shaped/finished edges.
Recognise when a tool is blunt or poorly adjusted.
Carry out basic sharpening and maintenance of chisels and plane irons.

1. Workshop Safety & Work holding

Brief introduction followed immediately by practical setup.

Participants practise:

Correctly positioning timber in a vice.
Using clamps and bench hooks.
Checking that timber is secure before starting work.
Safe stance and body positioning.
Keeping hands and fingers outside the cutting path.
Inspecting tools before use.
Safe handling and placement of sharp tools on the bench.

The emphasis is on establishing good habits that are then reinforced throughout the workshop.

2. Handsaw Practice

Short facilitator demonstration covering:

Different common saws and when to use them.
Cross-cut versus rip-cut.
Correct grip and stance.
Starting a cut with light, controlled strokes.
Following a marked line.
Using the full length of the saw.
Allowing the saw to cut rather than forcing it.
Supporting the offcuts correctly.

Participants then practise on timber:

Marking a square cut.
Starting a saw cut accurately.
Cutting timber to length.
Cutting to the waste side of a marked line.
Producing a reasonably square cut.
Repeating cuts to improve accuracy and control.

Facilitator circulates and corrects grip, stance, work-holding and hand position.

3. Chisel Practice

Short demonstration covering:

Chisel anatomy and cutting edge.
Correct grip.
Working with and across the grain.
Paring versus using a mallet.
Removing small amounts of material at a time.
Keeping both hands behind the cutting edge.

Participants practise:

Paring timber to a marked line.
Removing small amounts of timber.
Cutting a simple notch or housing.
Chiselling across the grain.
Cleaning up the bottom and edges of a recess.
Using a mallet safely and with control.

Participants can use their earlier saw cuts to form part of the chisel exercise, helping connect the different tools.

4. Hand Plane Practice

Short demonstration covering:

Basic parts of a hand plane.
Checking and adjusting the blade.
Setting a light cutting depth.
Correct grip and stance.
Identifying grain direction.
Pressure at the beginning, middle and end of a stroke.

Participants practise:

Setting up and testing a plane.
Producing a fine shaving.
Planing a rough or sawn edge.
Planing timber with the grain.
Straightening and smoothing an edge.
Creating a small chamfer.
Adjusting the plane when it is cutting too heavily or unevenly.

The aim is for participants to feel the difference between a correctly adjusted plane and one that is poorly set.

5. Sharpening & Tool Maintenance

This section remains practical rather than lecture-based.

Facilitator demonstrates:

Identifying a blunt edge.
Sharpening stone or diamond plate setup.
Basic bevel angle.
Using a honing guide.
Raising and removing a burr.
Honing the cutting edge.

Participants practise:

Setting a chisel or plane iron in a honing guide.
Sharpening/honing the bevel.
Removing the burr.
Checking the finished edge.
Returning the blade to the tool and testing it on timber.

Where possible, participants compare the tool's performance before and after sharpening.

Basic maintenance is incorporated during the exercise:

Cleaning tools.
Protecting cutting edges.
Checking handles and components.
Preventing rust.
Correct storage.

6. Combined Skills Exercise

Participants complete a simple timber exercise using all three tool groups.

For example:

Measure and mark a piece of timber.
Saw it accurately to length.
Saw the sides of a notch.
Chisel out the waste.
Clean up the joint with a chisel.
Plane an edge smooth and straight.
Add a small chamfer to the finished piece.

The finished object is less important than practising accuracy, control and safe technique.

Workshop Finish

Group clean-up followed by a quick recap:

Correct saw technique.
Safe chisel hand position.
How to recognise grain direction.
Correct plane setup.
Signs that a cutting edge needs sharpening.

• How to safely store and maintain the tools.

Contact the host of Intro to Hand Tools